Open AccessPeer ReviewedPublished Monthly Since 2007 Vol. 19, Issue 12 · November 2026Media Kitinfo@guident.net

Chairside Fabrication of Flexible Cast

  • Dr. Manesh LahoriProfessor & Head
  • Dr. Manpreet Kaur Department of ProsthodonticsP.G Student
Guident · Volume 10, Issue 1 (December 2016)Published December 20168 min read4 figures

INTRODUCTION

The Flexible casts are available chairside in minutes, allowing for extraoral evaluation of the preparations before impression making.Flexible casts are elastic in nature thus have minimum defects and the chances of surface distortion are eliminated. Flexible die materials are used to fabricate flexible dies to make provisional crowns and indirect composite acrylic resin inlays and also for fabricating post coping in overdentures.

Advantages:

  1. It is easy to fabricate
  2. Chairside time is reduced
  3. It is reusable unlike the stone casts.
  4. Biocompatible
  5. Good reproduction of surface details
  6. Elastic in nature, thus reduces chances of distortion.
  7. Allows the evaluation of preparation extra orally

Disadvantages:

  1. Materials used to fabricate the cast are expensive.
  2. At times, they adhere to the already set impression.

According to a study by Gerrow et al, the surface detail reproduction by the flexible die materials is as good as that of dental stone. When no separator was used, the polyvinyl siloxane impression materials were found to be incompatible with the polyvinyl siloxane die materials because the dies failed to separate from the impression. When a separator was used, the impression did separate from the die material, but the detail reproduction was significantly worse than dental stone.

Steps to Fabricate flexible die:

  1. A separator is applied wherever necessary.
  2. An impression is made intra-orally with standard impression materials.
  3. The die is made by pouring the impression with a flexible die material.
  4. When set, the die is removed from the impression, and the restoration is then fabricated and finished on the flexible die.

Various Commercially Available Die Materials:

  1. Impregum F (ESPE, Norristown, Pa).
  2. Imprint (3M Dental Products, St. Paul, Minn).
  3. Extrude Medium (Kerr Mfg. Co., Romulus, Mich).
  4. Blu-Mousse (Parkell Bio-Materials Div., Farmingdale, N.Y).
  5. Panasil Medium (Kettenbach-Dental, Kettenbach, Germany)
  6. Extrude Extra (Kerr Mfg. Co., Romulus, Mich)
  7. EOS Bluephase-P (Ivoclar/Vivadent, Schaan, Lichtenstein)
  8. DieKeen(Modern Materials Heraeus Kulzer, South Bend, Ind).
  9. Mach 2 Silicone (Parkell, Farmingdale,N.Y.)
  10. Hot Melt Adhesive material (3M Scotch-Weld hot melt adhesive; 3M)

Hot Melt Adhesive is a thermoplasticmaterial usually supplied in sticks, which are melted using an electric gun. It typically consists of a base material such as an ethylene-vinyl acetate copolymerwith additives such as wax, resins, plasticizers, andpigments. HMAs do not adhere to elastomeric impression materials. This allows easy separation of impressions made with any material, including polyvinyl siloxane without the need for a separating agent.

Obtaining the flexible cast from the definitive impression eliminates the need for an additional impression, reduces the time needed for the procedure, and improves the accuracy of flexible cast details. HMAs are also less expensive than elastomeric impression materials. The Mach 2 die system is a flexible die system developed for the fabrication of indirect composite inlays. The material is a specially formulated polyvinyl siloxane die material intended to be injected into an impression, forming slightly flexible tooth-preparation dies for use minutes after the impression is poured. The material produces accurate dies, hasa short setting time of 6 to 8 minutes, can be trimmed by using a round bur or sharp scalpel, and is slightly flexible, preventing fracture of the cast or acrylic resin provisional restoration during separation of the cast and impression.

Because the flexible cast is available chairside within minutes of impression making, it can be used to evaluate the preparations for adequate reduction, taper, and path of insertion. Minor corrections can be made to the tooth preparations before making a final impression. A new silicone die is not necessary for provisional fabrication, provided that the finish line of the prepared teeth has not been altered.

USES

I. Flexible Cast to fabricate Provisional Restoration:


The use of flexible casts and dies for the chairside fabrication of interim restorations can overcome the drawbacks of the direct technique andprovide a safe and biocompatible fabrication process. The elasticity of these casts allows easy removal of the interim restoration after complete setting, and the integrity of the casts is maintained. Different elastomeric impression materials and consistencies have been used to make flexible casts.
Although materials such as Polyvinyl Siloxane have excellent dimensional stability, they are relatively expensive and adhere to the already set impression material.For this reason, a second alginate impression is usually made to produce the flexible cast. Hot melt adhesive material (HMA) overcome the drawbacks of the expensive materials and is used for the fabrication of flexible casts.

PROCEDURE:

i) To Fabricate Flexible Cast using Hot Melt Adhesive for Single Unit Provisional Restoration:


1. A putty index mould is made of the tooth intended for preparation including neighbouring tooth on each side.
2. The tooth is prepared in the usual manner.
3. The definitive impression of the prepared tooth and the surrounding tissue is made with the preferred impression material.
4. To produce the flexible cast, the prepared and adjacent teeth are filled by injecting the heated Hot Melt Adhesive materialwith an electric gun. (Fig.1)
5. When the Hot Melt Adhesive material cools, it is removed from the definitive impression.(Fig.2)
6. If there are bubbles or defects on the cast small amount of the heated HMA material is applied to the impression and is replaced in the impression.
7. The flexible cast is re-seated into the preoperative index mould and examinedcarefully for complete seating.
8.A mix of autopolymerising resin material is prepared and placedinto the index mould.
9. Immediatelythe flexible cast is seated fully into the index mould and both are held firmly in place by hand or with a rubber band until the resin completely polymerizes.
10. After the resin has completely polymerized, the putty index mould is separated from the flexible cast.
11. Flexibility allows easy removal of the interim restoration without damaging either the cast or the restoration.
12.Excess material is trimmed and undercuts are removed, and the interim restoration is shape with rotary instruments in the usual manner and cemented in patient’s mouth.

Clinical figure

Fig. 1 Hot Melt Adhesive material is injected in the mould

Clinical figure

Fig. 2 Flexible cast of Hot Melt Adhesive

Clinical figure

Fig. 3 Provisional Restoration fabricated on the flexible cast

Clinical figure

Fig. 4 Finished Provisional Restoration on the prepared tooth

ii)To Fabricate Flexible Cast using Mach-2 silicone die material for Multi-Unit Provisional Restoration:

In additionto provisional fabrication, the flexible cast allows the clinician to evaluate the preparations for undercuts and proper path of insertion before making the final impression.

  1. For FPDs,the ponticshould be waxed into the edentulous area of the study cast, and modified with wax to obtain ideal contours, contacts, and occlusion.
  2. Modified diagnostic cast is lightly lubricatedand an impression is made using a high viscosity elastomeric impression material to provide an adequate bulk of material at the margins of the provisional restoration.
  3. An irreversible hydrocolloid impression should be made of the prepared teeth in the same area as in the elastomeric overimpression.
  4. Then, Mach-2 material is syringedinto the impression to minimize bubbles.
  5. The flexible cast should be trimmed with a sharp scalpel so that it fits properly into the overimpression.
  6. Then a sufficient amount of autopolymerizing acrylic resin should be mixed andfilled in the overimpression.
  7. The cast should be seated in the overimpression completely and the acrylic resin is allowed to polymerize completely.
  8. After the acrylic resin has set, the provisional restoration is removedfrom the overimpression, it is then trimmed and cemented onto the teeth.

II. Flexible Cast to fabricate Post-Coping for Overdentures:

When coping margins are within the crevice, accurate intraoral fabrication becomes difficult because the fit and finish of the pattern margins cannot be adequately evaluated. The use of a cast that is available chairside within minutes of impression making would save valuable chairside time and improve the accuracy of the coping margins.
Since, Stone casts require 1 hour for setting. They sometimes fracture during separation of the cast from the impression, requiring multiple pours and/or patient visits. Given the disadvantages of stone casts, the use of a flexible cast available chairside within minutes of impression making would be desirable.
Customposts are fabricated directly in the root canal with pattern resin. Careful intraoral adjustments should be done to relieve binding areas, combined with the volumetric shrinkage of the resin pattern that can produce posts that seat passively into the canal. Completion of the post-coping restorations is accomplished by using the flexible cast. The procedure is efficient, uncomplicated, and produces accurate, well-fitting restorations. Post patterns can be fabricated and adjusted directly in the root canals. Minor undercuts can be identified and removed.
The use of a polyvinyl siloxaneelastometric impression material is not recommended for making the final impression because of its incompatibility with the Mach 2 silicone die material. A flexible cast was madefrom this impression and was used to complete thefabrication of the coping restorations.

III. Flexible Cast to fabricate indirect composite onlay/inlay provisional restorations:

Flexible casts can be fabricated for onlay preparations to give clear internal detail,margins are easily identified, and excess acrylic resinremoved to produce a completed acrylic resin provisionalrestoration. There are increased number of wallsand line angles in an onlay preparation, thus, this method isespecially useful for examining the onlay and even the inlay preparation for clinicalacceptability before impression making.
The indirect technique minimizes distortion due to polymerization shrinkage because the acrylic resin provisional is allowed to set completely on the cast. The Mach 2 silicone die material does not adhere to the acrylic resin and separation is easy. Because the flexible cast is not destroyed during separation of the cast fromvthe impression, reuse of the cast for margin repair or contact modification is possible.

CONCLUSION

Although a stone dies can be used, the flexible die material sets more rapidly and allows the finished restoration to be easily removed from the die. Also while fabricating the elastic cast, the inclusion of 1tooth on either side of the preparations will serve as a stop and help to prevent errors in seating the cast into the overimpression. Incomplete seating will result in a provisional restoration that is in hyperocclusion. Overseatingthe cast can produce thin areas in the provisional restoration because of pinching of the cast against the overimpression. Factors such as flexibility of the die, dimensional stability, and interactions between the die material or the separator and the impression materials should also be considered when choosing a flexible die and impression system.

REFERENCES

  1. Jack D. Gerrow and Richard B. Price. Comparison of the surface detail reproduction of flexible die material systems.J Prosthet Dent 1998;80, 4:485-9.
  2. Kenneth G. Boberickand Thomas K. Bachstein.Use of a flexible cast for the indirect fabrication of provisional restorations. J Prosthet Dent 1999;82,1:90-3.
  3. Kenneth G. Boberickand David Wyke. Use of a flexible cast for fabrication of multiple post-coping overdenture restorations. J Prosthet Dent 1999;81,3:365-8.
  4. Mohiddin R. Dimashkieh, and Mohammad R. Rayyan. Chairside technique for expediting indirect interim restorations. J Prosthet Dent 2016;115,4:510-511.

Disclaimer from Guident

The views and opinions expressed in articles published in Guident are solely those of the authors and do not necessarily reflect the views of the editors, the editorial board or the publisher, Ivory India. Guident does not endorse any product, technique or treatment described. Clinical content is intended for qualified dental and medical professionals and is not a substitute for individual clinical judgement. Guident, its editors and the publisher accept no liability for any consequence arising from the use of information published in the journal.

How to cite this article

Dr. Manesh Lahori, Dr. Manpreet Kaur Department of Prosthodontics. Chairside Fabrication of Flexible Cast. Guident. 2016 Dec;10(1). Available from: https://ivoryindia.in/articles/prosthodontics/chairside-fabrication-of-flexible-cast.html

Related articles

More in Prosthodontics

All 386 articles
Vol. 10, Issue 1 · December 2016

Changing Smiles - Changing Concepts

When considering aesthetic dentistry the two main objectives are to create teeth of pleasing inherent proportions and of pleasing proportions to one another and to create a pleasing tooth…

Dr. Rathika Rai

Call for papers

Publish your clinical work in Guident

Original research, case reports and review articles are welcomed from clinicians and researchers worldwide. Every submission is assessed by the editorial board.