Open AccessPeer ReviewedPublished Monthly Since 2007 Vol. 19, Issue 12 · November 2026Media Kitinfo@guident.net

The "Button Stent"- a New Approach for Decompression

  • Dr. Muthukumar RPost Graduate
  • Dr. Y.A. BindhooReader & Guide
  • Dr. VR Thirumurthy Depaertment of ProsthodonticsProfessor & H.O.D

Sri Ramakrishna Dental College and Hospital, Coimbatore, Tamilnadu, India

Guident · Volume 9, Issue 2 (January 2016)Published January 20166 min read6 figures

Abstract

Marsupialisation is an established treatment option for the management of large odontogenic cysts, but the surgical procedure has to be supplemented with a proper prosthetic stent to maintain the patency of the cavity and prevention of food debris into the cavity. The purpose of this article is to describe a clinical report involving a different method of fabrication of a semi fixed stent.

INTRODUCTION

Untreated cysts tend to increase in size and become infected.1 The cyst may enlarge eroding the adjacent vital structures of maxilla and mandible . In certain clinical situations , marsupialisation of the cysts have been recommended. Marsupialisation is a treatment option which opens the cavity into the mouth.1-4Following marsupialisation, the patient has a cavity which requires a pack or stent to prevent premature closure of the opening. A variety of methods and techniques have been previously used for the fabrication of decompression stents to maintain the patency of the cystic opening.5-15

Ramsey used clasp retained devices for the drainage of marsupialised cysts.5 Ziccardi used a fenestration technique for large dentigerous cysts.6 Carter described customised stents for marsupialisation.8 Rehman described the ‘oral grommet’.9 Tolstunov used a catheter for marsupialisation.10 Singh described the use of endotracheal tube tailored as a stent.11 Catunda described a decompression device using luer syringe.14 This case report describes the use of a commonly available ‘Press’ button for fabrication of a semi fixed stent.

CLINICAL REPORT

An 18 year old female patient was referred from the department of oral and maxillofacial surgery for the fabrication of stent to maintain the patency of the oral opening caused by marsupialisation of an odontogenic cyst in relation to 25. A buccal approach had been used for the marsupialisation procedure. An impression of the defect was made with modelling plastic impression compound(Y-dents, MDM, Delhi,India) and medium body elastomer(3M, ESPE, Germany) and a pick up impression was made with irreversible hydrocolloid impression(Tropicalgin,Zhermack, Italy).The impression was obtained in two parts which were then reapproximated. Examination of the impression revealed that the defect was oriented in a superio-palatal direction from the buccal side (Fig 1).

This created a severe undercut which eliminated the possibility of a stent like extension from a palatal plate. Various other treatment options included the use of catheters , airways and syringes sutured to the cyst opening. But the sutures themselves may act as reservoirs of infection. A commonly available press button was therefore used for the fabrication of a stent (Fig 2).

PROCEDURE

  1. Impression was poured with type III dental stone(Goldstone, Asian chemicals, Rajkot,India) and a cast was made.
  2. The male component of a ‘press’ button was adapted over the buccal surface of the adjacent premolar24 so as to approximately coincide with the determined path of insertion of the stent and slightly trimmed so that it was confined within the contours of the buccal surface (Fig 3).
  3. The male component was kept apart and a normal stent involving only the defect and extending over the buccal surface of 24 was fabricated with clear heat polymerised acrylic resin(DPI, Mumbai, India ).
  4. The stent was trimmed, polished and tried in the patient’s mouth.
  5. The male component was sandblasted for proper bonding.
  6. After proper isolation, the buccal surface of 24 was treated with etchant and bonding agent (3M,ESPE,Germany) according to manufacturer’s instructions. Light polymerised composite resin(3M,ESPE,Germany) was applied over the tooth facing part of the male component and positioned in the same way as it was in the cast and light polymerised(Fig 4).
  7. A thin layer of wax was added inside the female component to prevent blocking of the spring action in it and press locked over the male component in the mouth.
  8. The part of the stent extending over 24 was adequately relieved to accommodate the press button in the mouth.
  9. Vaseline was applied over the mucosa surrounding the button . Clear autopolymerising acrylic resin (DPI, Mumbai, India) was mixed and placed on the stent extension and an intraoral pick up of the female component was made with the stent in place.
  10. After polymerisation, the stent with the female component was removed from the mouth , trimmed and polished.(Fig 5)
  11. The “Button stent “ was now press locked over the male component and the patient was able to lock and unlock the stent with ease for regular cleaning.(Fig 6)
Clinical figure
Fig 1. – impression of the defect extending in a superiopalatal direction.
Clinical figure Clinical figure
Fig 2. – The female(A) and male(B) components of the press button. Fig 3. – The male component adapted over the
buccal surface of adjacent teeth in the cast.
Clinical figure Clinical figure Clinical figure
Fig 4. – The adapted male component bonded
over the surface of the teeth intraorally.
Fig 5. – The finished ‘Button stent’. Fig 6. – The ‘Button stent’ locked in place intraorally.

DISCUSSION

The case report described the difficulty in the path of insertion of the stent and the fabrication of a Button stent to overcome this situation. The button stent can be fabricated in a large number of clinical situations involving cysts in close proximity to a tooth , especially in the maxillary arch where bonding to the buccal surface will not interfere with occlusion. The previously used decompression stents using catheters , endotracheal tubes , luer syringes which were sutured in place allowed for accumulation of food debris because of the open communication and also the sutures itself where a source of infection in the long term as these devices will have to be used for a considerable length of time.

The advantage of this technique is that it is easy to fabricate , comfortable for the patients, can be easily removed , cleaned and reinserted by the patients themselves , are large enough to block the entry of food debris and at the same time passive enough to permit drainage of the cystic contents. The disadvantage of this technique is that it requires additional chair side time with proper isolation for the bonding of the component in the mouth and it is mostly limited to the maxillary arch as it may interfere with occlusion in the mandibular arch.

SUMMARY

A case report was described involving the use of a different method of fabrication of a decompression stent, which is easy to fabricate , economical , hygienic and comfortable to the patient.

REFERENCES

  1. Seward GR, Harris M, McGowan DA. Killey and Kay’s outline of oral surgery part one.2nd ed. Bombay . Varghese publishing house ; 1992 .p. 282-283.
  2. Pogrel MA, Jordan RC. Marsupialization as a definitive treatment for the odontogenic keratocyst. J Oral Maxillofac Surg 2004;62:651-5.
  3. Pogrel MA. Treatment of keratocysts: the case for decompression and marsupialization. J Oral Maxillofac Surg 2005;63:1667-73
  4. Enislidis G, Fock N, Sulzbacher I, Ewers R. Conservative treatment of large cystic lesions of the mandible: a prospective study of the effect of decompression .Br J Oral Maxillofac Surg 2004;42:546-50.
  5. Ramsey WO, Denegri RF, King WF. Clasp retained devices for drainage of marsupialized cysts. J Oral Maxillofac Surg 1982;40:759-61.
  6. V.B. Ziccardi, T.I. Eggleston, R.E. Schneider. Using fenestration technique to treat a large dentigerous cyst. J Am Dent Assoc 1997; 128:201–205
  7. Neyra MR . Decompression prosthesis. Med Oral 2001;6:306-9.
  8. Carter LM, Carr P, Wales CJ, WhitfieldPH. Customised stents for marsupialisation of jaw cysts.Br J Oral Maxillofac Surg. 2007;45:429-31
  9. Rehman KU, Opie N, Parmar S, Jeynes P. The oral grommet.Br J Oral Maxillofac Surg 2008;46:692-3
  10. Tolstunov L. Marsupialization catheter. J Oral Maxillofac Surg 2008;66:1077-9


More References are available on request

Disclaimer from Guident

The views and opinions expressed in articles published in Guident are solely those of the authors and do not necessarily reflect the views of the editors, the editorial board or the publisher, Ivory India. Guident does not endorse any product, technique or treatment described. Clinical content is intended for qualified dental and medical professionals and is not a substitute for individual clinical judgement. Guident, its editors and the publisher accept no liability for any consequence arising from the use of information published in the journal.

How to cite this article

Dr. Muthukumar R, Dr. Y.A. Bindhoo, Dr. VR Thirumurthy Depaertment of Prosthodontics. The "Button Stent"- a New Approach for Decompression. Guident. 2016 Jan;9(2). Available from: https://ivoryindia.in/articles/prosthodontics/the-button-stent-a-new-approach-for-decompression.html

Related articles

More in Prosthodontics

All 386 articles
Vol. 9, Issue 3 · February 2016

Acupuncture in Prosthodontics

Authors : Dr Rohit Raghavan , Dr Shreshta Sathish . Abstract Acupuncture has been accepted to effectively treat chronic pain by inserting needles into the specific ‘‘acupuncture points’’…

Dr Rohit Raghavan

Call for papers

Publish your clinical work in Guident

Original research, case reports and review articles are welcomed from clinicians and researchers worldwide. Every submission is assessed by the editorial board.