Open AccessPeer ReviewedPublished Monthly Since 2007 Vol. 19, Issue 12 · November 2026Media Kitinfo@guident.net

A Comparative Evaluation of Anti-Microbial and Three Physical Properties of High Impact Acrylic Resin After Incorporating Varying Percentage of Zinc Oxide and Zirconium Dioxide Nanoparticles – an in Vitro Study

  • Dr. Poonam YadavP.G. Student
  • Dr. Suneetha RaoProfessor & Head
  • Dr. AshokProfessor

Department of Prosthodontics, Vydehi Institute of Dental Science & Research Center, Bengaluru, Kar.

Guident · Volume 18, Issue 8 (July 2025)Published July 202518 min read10 figures

ABSTRACT

Background and objectives: Polymethyl methacrylate (PMMA) is widely used in dentistry for different purposes.it is known that denture bases may act as a reservoir of microorganisms and contribute to oral diseases and tissue damage. High impact heat-cured PMMA resin material was developed mainly to get rid of the low impact strength problem of conventional resins. An optimized resin material should exhibit a positive biologic response (i.e., decreased adhesion of candida) while maintaining the desired physical properties.

The present study aimed to evaluate and compare antimicrobial and three physical properties namely impact strength, surface strength, surface hardness on addition of 2.5%, 5%, 7.5% and 10% wt. ZnO nanoparticle and zirconium dioxide nanoparticle to high impact PMMA (heat cure) resin and furthermore, to create such a PMMA nanocomposite material with enhanced antimicrobial and mechanical properties. These individual nanoparticles have been tested in various studies, but a combination of both in various concentrations hasn’t been done, therefore this study was undertaken.

Materials and methods: A total of 375 samples divided into 5 groups were fabricated for the present study. 75 samples incorporated with ZrO2 and ZnO nanoparticles by wt. 2.5% ,75 samples incorporated 5% wt. group ,75 samples involved 7.5%wt, 75 samples involved 10% wt. group and 75 samples were control group i.e., without any nano partical addition were fabricated.

The physical properties like impact strength, surface hardness and surface roughness of these samples was tested. The impact strength of the sample was tested using impact tester. The same sample was subjected to the testing of surface hardness by the Vickers hardness tester. And surface roughness of sample was tested with profilometer.

Furthermore, the samples of each group were tested for antimicrobial activity using Kirby Bauer disk diffusion method. It was incubated at 37 degrees centigrade for 24 hours to check the zone of inhibition.

The values collected were tabulated and subjected to statistical evaluation in which pairwise intragroup comparison was done using Bonferroni post hoc analysis.

Results: The results of this study demonstrated that varying the concentrations of ZnO and ZrO? nanoparticles significantly influences the physical properties of the tested materials, namely impact strength, surface roughness, and surface hardness.

The group with 7.5% ZnO and ZrO? consistently exhibited the highest impact strength (1.95 ± 0.4 j) and surface hardness (24.21 ± 0.41 hv), along with a markedly increased surface roughness (3.91 ± 1.01 µm). In contrast, the 10% ZnO and ZrO? group displayed the lowest impact strength (1.33 ± 0.3 j) and surface hardness (16.12 ± 0.19 hv), but showed moderate surface roughness (2.54 ± 0.78 µm).

Statistical analyses revealed significant differences among the groups for all tested properties (p < 0.05), indicating that nanoparticle concentration is a critical factor in determining material performance.

Additionally, microbial activity analysis showed a significant association between nanoparticle concentration and colony-forming unit counts (p < 0.05). The CFU count was low in control group, moderate in 2.5%, 5% and 7.5% ZnO and ZrO2, and high in 10% ZnO and ZrO2, highlighting increase in microbial activity with increasing concentration of nanoparticles.

Interpretation and conclusion: The increasing concentrations of ZrO2 and ZnO nanoparticles into high impact heat cure PMMA resin showed an increase in the impact strength in an ascending order, except after a point (7.5% conc.) After which it showed a decrease. An increase in the surface hardness in an ascending order was seen, except after a point (7.5% conc.) After which it showed a decrease. An increase in the surface roughness in an ascending order, was noted and it was highest in the 7.5% group and in 10% surface roughness decreased This attributed to a higher roughness with increasing concentration of the fillers up to 7.5% and further reducing with 10%.The increasing concentrations of ZrO2 and ZnO nanoparticles into high impact heat cure PMMA resin showed an increase in the antimicrobial activity in an ascending order and was highest in 10% group, moderate in the 2.5%, 5% and 7.5% groups, owing to the fact that addition of ZrO2 and ZnO nanoparticles provides better antimicrobial resistance than the control group with no fillers added.

According to this, the incorporation of ZrO2 and ZnO nanoparticle composites in heat-cured high-impact resin, significantly enhances both its mechanical and antimicrobial properties. This innovative formulation not only improves strength and durability but also boasts enhanced antimicrobial characteristics. As a result, this nano composite represents an optimal solution for advancing the performance and safety of high-impact heat-cured resins, making it a transformative choice for applications where mechanical resilience and hygiene are paramount.

Keywords-

Denture base resins, high impact PMMA, Nanoparticles, Antimicrobial Property, Impact Strength, Surface Roughness, Surface Hardness.

INTRODUCTION

The use of acrylic dentures remains a cornerstone in prosthodontic rehabilitation for patients with partial or complete edentulism. Owing to their affordability, ease of fabrication, and acceptable clinical outcomes, acrylic dentures—especially those made from polymethyl methacrylate (PMMA)—continue to be widely accepted globally(1). Although alternatives like implant-supported prostheses exist, removable acrylic options remain favorable for individuals with compromised immunity or poor oral hygiene due to their self-cleansable nature and ease of tissue evaluation.(2)

PMMA, the most utilized denture base material, comprises a mixture of polymer and monomer components, exhibiting inherent porosity and surface irregularity(3,4). These properties, while beneficial for fabrication, create a conducive environment for microbial colonization, especially by Candida species. The oral cavity hosts a diverse microflora, but denture use—particularly in the maxillary arch due to its larger denture-bearing surface—alters this balance, often resulting in denture-related pathologies like denture stomatitis (2).

Denture stomatitis is a prevalent inflammatory condition triggered by multiple factors, including poor hygiene, prolonged denture use, occlusal trauma, and continuous wear. Biofilm formation by Candida albicans on the intaglio surface of dentures is pivotal in its pathogenesis (5). Critical factors influencing microbial adherence include surface roughness, porosity, and hydrophobicity of the denture base material. Hence, smoother, more hydrophilic materials with minimal porosity are recommended to limit microbial colonization (6).

Despite its popularity, PMMA possesses suboptimal mechanical properties, notably low transverse and impact strength, predisposing it to frequent fractures (7,8). Various strategies have been explored to enhance PMMA, including the incorporation of fillers like chitosan, titanium dioxide (TiO?), silicon dioxide (SiO?), and silver nanoparticles. These additives aim to improve not only antimicrobial resistance but also impact strength and surface hardness (9). However, the use of metal fillers often compromises esthetics, limiting their widespread clinical application (9).

Recent advancements in nanotechnology offer promising solutions. Nanoparticles, due to their high surface area and unique mechanical characteristics, are increasingly utilized to enhance dental materials. Among them, zinc oxide (ZnO) and zirconium dioxide (ZrO?) nanoparticles have emerged as effective agents. ZnO exhibits potent antimicrobial properties, while ZrO? provides excellent mechanical reinforcement, biocompatibility, and superior esthetics compared to traditional metal fillers (10,11).

Studies indicate that ZrO? enhances the physical properties like impact strength of PMMA, reducing porosity and improving hardness (12,13). ZnO, on the other hand, is a well-established antimicrobial agent used in dental applications like root canal sealers. Although both nanoparticles show individual benefits, limited research exists on their combined effect within high-impact PMMA.

This study was therefore undertaken to explore the synergistic effects of incorporating both ZnO and ZrO? nanoparticles in various concentrations into high-impact PMMA resin. The aim was to evaluate enhancements in antimicrobial efficacy against Candida albicans and improvements in key physical parameters, including impact strength, surface roughness, and surface hardness. The dual addition could potentially yield a novel PMMA composite material with superior functional and biological performance, setting a new standard for denture base materials in modern prosthodontics.

MATERIALS AND METHOD

The materials and armamentarium used for this study are as follow :Armamentarium:(FIG 1_)Wax knife, rubber bowl, and plaster spatula (Fig.1a) were used for mixing materials.Heat-curing denture flask and clamp, porcelain mixing jar, trimming burs, stones, sandpaper mandrel, disk, and polishing buff were also employed.Vernier caliper (Fig.1b) ensured accurate measurements. Moulds used are shown in PMMA (Lucitone 199 HI, Dentsply Sirona) served as the base material.ZnO nanoparticles (30 nm) and ZrO? nanoparticles (30–50 nm) acted as reinforcing agents.Candida albicans (from Dextrose Technology Pvt. Ltd.), Sabouraud Dextrose Broth (SDB), silane coupling agent (Silane-X, India), modeling wax (DPI), and cellophane sheet were also used.

Clinical figure

Figure-1a

Clinical figure

Figure-1b

Clinical figure

Figure-1c

Clinical figure

Figure-1d

Clinical figure

Figure-1e

Clinical figure

Figure-1f

Clinical figure

Figure-1g

Clinical figure

Figure-1h

Clinical figure

Figure-2: Zone Of Inhibition Against C. albicans

Different Equipments used

Impact Testing Machine (Instron), Digital Vickers Hardness Tester (Blue Star Engineering & Electronics), and a Profilometer (non-contact optical interferometric) were employed for evaluations.

METHODOLOGY

This in-vitro study was conducted at Vydehi Institute of Dental Sciences and Research Centre, Bangalore. Iec number

Experimental Material Preparation:

High-impact heat-cured PMMA resin was used as the control. ZnO and ZrO? nanoparticles (99.56% purity) were added in 2.5%, 5%, 7.5%, and 10% weight concentrations. A 1% silane coupling agent was incorporated.

Mould Fabrication:
Three types of stainless steel moulds were fabricated as per ISO 1567:

  • Impact strength test: rectangular bar (60×7×4 mm)
  • Surface hardness and roughness: rectangular bar (30×10×2.5 mm)
  • Antimicrobial testing: disk (5 mm diameter × 3 mm thickness)

Wax Pattern Preparation:

375 wax patterns were made by pouring molten wax into metal moulds treated with petroleum jelly. Only flawless patterns were selected.

Flasking and Dewaxing:

Wax patterns were invested in dental plaster using a mechanical vibrator. Dewaxing was done at 100°C for 5 minutes. After removing wax with boiling water, separating media (Cold Mould Seal; DPI) was applied using a camel hair brush.

SPECIMEN FABRICATION

Experimental Group (300 specimens):

Fifteen specimens were created for each concentration group across tests (antimicrobial, impact strength, hardness, roughness).

Control Group (75 specimens):

Control group specimens were made by mixing PMMA resin powder and monomer in a 3:1 ratio, packed during the dough stage, and bench cured for 1 hour. Polymerization followed a short curing cycle (74°C for 2 hrs + terminal boiling for 1 hr). Specimens were bench cooled and deflasked.

Post-Retrieval Treatment:

Excess resin was trimmed with acrylic trimmers, surfaces were polished with pumice, and final measurements were verified using a Vernier caliper. All specimens were stored in distilled water at 37°C for 1 week to eliminate unreacted monomers.

Fabrication of Reinforced Specimens:

ZrO? and ZnO nanoparticles were weighed for target concentrations (2.5%, 5%, 7.5%, 10%) and treated with 1 wt.% silane coupling agent. This powder was blended with monomer (3:1 ratio) and processed similarly to control groups. Reinforced groups were labeled as E2, E3, E4, and E5 respectively.

All specimens were examined for defects. Acceptable samples were retained and stored in water for one week before testing.

SAMPLE TESTING

Impact Strength Test:

Conducted using an Izod pendulum impact testing machine (Zwick, Germany). Each un-notched specimen was mounted vertically, clamped 2.5 cm into the clamp and 3.5 cm above, with the pendulum striking at 5.5 m/s. The absorbed energy in joules was digitally recorded (least count 0.01 J).

Surface Hardness Test:

Rectangular specimens (30×10×2.5 mm) were tested using a digital Vickers microhardness tester. A 50-gf load was applied for 5 seconds using a diamond pyramid, and the Vickers Hardness Number (VHN) was recorded.

Surface Roughness Test:

A non-contact optical profilometer recorded the surface roughness (Ra). Three readings were taken per specimen and averaged to obtain the final roughness value in micrometers (µm).

Antimicrobial Testing

Culture Preparation:

Candida albicans cultures were obtained from the Microbiology Department. Colonies were transferred to a tube containing 3 ml of Sabouraud Dextrose Broth (SDB) and incubated at 37°C overnight.

Method:
Disc-shaped specimens were sterilized using low-temperature steam and formaldehyde. Each specimen was placed in a well of a culture plate. A 50 µL suspension of C. albicans was inoculated on the specimen surface and incubated with the lid slightly open for 2 hours in sterile conditions.

Subsequently, each well was filled with 950 µL of SDB. Wells with both suspension and SDB acted as positive controls; SDB-only wells served as negative controls. Plates were shaken using an orbital shaker in a 37°C incubator for 24 hours.

Colony-forming units (CFU) of C. albicans were then quantified using a serial dilution method followed by spreading on agar plates. The zone of inhibition was observed and recorded.

SUMMARY OF RESULTS

The study used SPSS for statistical analysis of five groups of PMMA reinforced with varying concentrations of ZnO and ZrO? nanoparticles. Descriptive and inferential statistics were performed, with non-parametric tests due to non-normal distribution (Shapiro-Wilk p < 0.05). The Kruskal-Wallis H test and Bonferroni post-hoc analysis were applied.

Impact Strength:

Highest impact strength was recorded in the 7.5% group (1.95 ± 0.4 J), followed by 5%, 2.5%, control, and the lowest in the 10% group. Significant differences (p < 0.05) were observed between multiple group pairs, confirming the influence of nanoparticle concentration.

Surface Roughness:

The 7.5% group showed the highest roughness (3.91 ± 1.01 µm), while the control had the lowest (1.99 ± 0.37 µm). Differences between groups were statistically significant (p < 0.05). Notable differences were found between 2.5% vs. 5%, 2.5% vs. 7.5%, 5% vs. 10%, and 7.5% vs. 10%.

Surface Hardness:

Surface hardness was greatest in the 7.5% group (24.21 ± 0.41 HV), followed by 5%, 2.5%, control, and lowest in 10%. Statistically significant differences (p < 0.05) were noted among several group comparisons.

Antimicrobial Activity:

Control group showed low CFU, 10% showed moderate, and 2.5%, 5%, and 7.5% showed high CFU counts. Thus, 10% ZnO and ZrO? exhibited the highest antimicrobial activity. The differences were statistically significant (Chi-square p < 0.05).

Overall, 7.5% reinforcement provided optimal physical properties, while 10% showed superior antimicrobial efficacy.

DISCUSSION

1. Polymethyl Methacrylate (PMMA)

Removable dentures remain the most common prosthetic option for edentulous patients. These transfer chewing forces to the mucosa, which assumes non-physiological roles, compromising its function. PMMA has long been favored in prosthodontics due to its acceptable mechanical performance, low density, esthetics, affordability, ease of handling, and modifiable characteristics (14).

Despite its popularity, PMMA exhibits limitations—water sorption, poor flexural and impact strength—necessitating enhancements via additives such as fibers, nanoparticles, and nanotubes. High-impact PMMA was introduced to mitigate fracture risk, especially from accidental drops. This graft copolymer (e.g., Lucitone 199) is created by polymerizing PMMA with rubbery monomers like butyl acrylate. It exhibits double the impact strength of conventional PMMA and significantly improves denture durability under stress(15).

Biocompatibility is essential; PMMA must not irritate tissues, must resist solubility in oral fluids, and should chemically bond with artificial teeth. Mechanically, it must offer high modulus, resilience, and fatigue resistance.

2. Mechanical and Antimicrobial Properties

For optimal denture longevity and function, impact strength, surface hardness, surface roughness, and antifungal activity are critical.

Impact Strength(16)

Defined as the energy needed to fracture material under sudden force, impact strength ensures denture resilience against drops. Conventional heat-cured PMMA's impact strength ranges from 0.98 to 1.27 J. Surface defects, even microscopic, reduce resistance and serve as crack initiation points. The low wear resistance and hardness of PMMA demand material improvements. In this study, the IZOD pendulum machine was used for testing.

Surface Hardness(17)

Hardness determines ease of polishing and scratch resistance during cleaning and intraoral function. It correlates with polymer resistance to degradation and overall denture life. Insufficient hardness may lead to fracture and surface degradation, increasing microbial adhesion and aesthetic deterioration.

Surface Roughness(17,18)

Surface roughness refers to minor surface irregularities affecting food and microbial debris adherence. While hardness doesn’t directly influence microbial buildup, roughness contributes significantly to biofilm formation, particularly Candida albicans. Abrasive cleaning compounds and mechanical wear also raise roughness. Profilometers measure roughness, and modifying materials can reduce it.

Antimicrobial Activity(19,20)

PMMA inherently lacks antimicrobial properties. It’s rough, porous surface fosters microbial growth, particularly in the oxygen-poor, acidic oral cavity beneath dentures—ideal for Candida albicans. Colonization may lead to denture stomatitis. Studies have aimed to enhance PMMA using additives such as nanoparticles, fibers, plasticizers, metallic additives, biocides, and natural agents like essential oils. These improvements aim to make PMMA less susceptible to microbial adhesion and more resistant to infection.

3. Nanotechnology and Nanoparticles (10,11)

Nanotechnology introduces innovations in dental materials at the molecular level. Nanoparticles, ranging from 1–100 nm, offer unique biochemical properties, enabling targeted antimicrobial action and mechanical reinforcement.

These particles can penetrate cell walls, disrupt membranes, and serve as carriers for active agents, making them highly effective against pathogens. In dentistry, nanoparticles enhance wear resistance, toughness, and other key material properties. Additives such as nano-ZrO?, TiO?, SiO?, Al?O?, and E-glass fiber have been studied extensively.

Zirconium Dioxide (ZrO?)

Zirconia was chosen for this study due to its mechanical benefits and biocompatibility. It’s white and esthetically favorable compared to metallic fillers. Its inclusion improves transverse strength, fracture resistance, and durability. Ayad et al. and Zuccari et al. demonstrated increased modulus of elasticity, toughness, and hardness with zirconia reinforcement. Zirconia particles positively affect flexural strength and impact resistance through matrix integration and effective crack bridging. (21)

Zinc Oxide (ZnO)

ZnO nanoparticles offer antifungal and antibacterial benefits, particularly against Candida. ZnO also improves PMMA’s UV resistance, affordability, and safety. Cierech et al. found that ZnO at 0.75 mg/ml inhibits Candida, although distribution within the matrix can be challenging. The ZnO-PMMA composites showed reduced fungal growth and improved properties. (22)

Mechanical properties depend not only on filler type, size, and quantity but also on filler-matrix adhesion. Hence, both ZrO? and ZnO were used in this study at 2.5%, 5%, 7.5%, and 10% concentrations, treated with 1 wt.% silane coupling agent for enhanced bonding.

Even distribution of nanoparticles is vital. Beyond optimal filler levels, excessive particles disrupt matrix integrity, reducing mechanical strength. This study aimed to determine the most effective combination of ZnO and ZrO? in high-impact PMMA for improved mechanical and antimicrobial behavior.(8)

4. Discussion of Results

The study found that ZnO and ZrO? concentrations significantly affected PMMA’s physical and antimicrobial properties.

Impact Strength

Order:7.5%>5%>2.5%>Control>10%

The 7.5% group showed the highest impact strength (1.95 ± 0.4 J), attributed to better nanoparticle dispersion and interfacial bonding, which blocked crack propagation. The 10% group showed the lowest strength (1.33 ± 0.3 J), even lower than the control. This reduction may be due to oversaturation, which creates voids or matrix discontinuity. Similar trends were observed in studies by Asopa V and Suresh S (15).

Surface Hardness & Roughness

Hardness:7.5%>5%>2.5%>Control>10%

Roughness:7.5%>5%>10%>2.5%>Control

The 7.5% group had the highest hardness (24.21 ± 0.41 HV) and roughness (3.91 ± 1.01 µm). This correlates with the intrinsic hardness of the nanoparticles. The 10% group showed lowest hardness (16.12 ± 0.19 HV) but moderate roughness. This supports the notion that beyond a threshold, additional nanoparticles can disrupt structural integrity.

Other studies also confirm that ceramic fillers like zirconia enhance hardness and durability when used in appropriate concentrations.(21,22)

Antimicrobial Activity

The 10% group had the highest antimicrobial efficacy, reducing Candida significantly. Other groups (2.5%, 5%, 7.5%) showed moderate activity. This confirms that increasing nanoparticle concentration improves antimicrobial resistance, primarily due to ROS generation, membrane disruption, and ion release mechanisms. The antifungal activity was independent of surface roughness(19,23).

These findings align with literature indicating nanoparticle-infused PMMA can deform fungal structures, inhibit biofilm formation, and extend denture life.

Conclusion

Incorporating ZrO? and ZnO nanoparticles in high-impact PMMA enhances its mechanical strength, antimicrobial activity, and overall performance. Clinically, this reinforced PMMA is particularly beneficial for dentures under high masticatory forces—e.g., distal extension bases, overdentures, single complete dentures, long-term provisionals, and implant-supported prostheses.

While individual studies exist for ZrO? and ZnO separately, this study uniquely investigates their combined effect. Further long-term and in-situ studies are necessary to assess performance in oral conditions and develop next-generation PMMA/ZrO?/ZnO composites

Clinical figure

REFERENCES

  1. Yassin IN, Abdulmajeed AA, Abd F, Al-Shammari K. The effect of adding micro zinc oxide filler to heat-polymerizing acrylic resin on some physical properties [Internet]. Vol. 3, Muthanna Medical Journal. 2016. Available from: www.muthjm.com
  2. Verma D, Garg PK, Dubey AK. Insights into the human oral microbiome. Vol. 200, Archives of Microbiology. 2018
  3. Kul E, Alada? L?, Yesildal R. Evaluation of thermal conductivity and flexural strength properties of poly(methyl methacrylate) denture base material reinforced with different fillers. Journal of Prosthetic Dentistry. 2016;116(5).
  4. Kamonkhantikul K, Arksornnukit M, Takahashi H. Antifungal, optical, and mechanical properties of polymethylmethacrylate material incorporated with silanized zinc oxide nanoparticles. Int J Nanomedicine. 2017;12.
  5. Hannah VE, O’Donnell L, Robertson D, Ramage G. Denture Stomatitis: Causes, Cures and Prevention. Vol. 6, Primary dental journal. 2017.
  6. Nejatian T, Nathwani N, Taylor L, Sefat F. Denture base composites: Effect of surface modified nano-and micro-particulates on mechanical properties of polymethyl methacrylate. Materials. 2020;13(2).
  7. Baba Y, Sato Y, Owada G, Minakuchi S. Effectiveness of a combination denture-cleaning method versus a mechanical method: comparison of denture cleanliness, patient satisfaction, and oral health-related quality of life. J Prosthodont Res. 2018;62(3).
  8. Leão R de S, Moraes SLD de, Gomes JM de L, Lemos CAA, Casado BG da S, Vasconcelos BC do E, et al. Influence of addition of zirconia on PMMA: A systematic review. Vol. 106, Materials Science and Engineering C. 2020.
  9. Sesha Reddy P, Reddy J. A Comparative Evaluation of Measuring Impact Strength of Heat Cure Acrylic Denture Base Resin With and Without Addition of Zirconia Nano-Particles-An In Vitro Study [Internet]. Vol. 25. 2021. Available from: http://annalsofrscb.ro
  10. Ehsan Al-Douri M, Mouyad Sadoon M. Flexural Strength, Hardness and Surface Roughness of 3D Printed Denture Base Resin Reinforced by Zinc Oxide Nanoparticles [Internet]. 2023. Available from: www.jrmds.in
  11. Qasim S Bin, Kheraif AA Al, Ramakrishaniah R. An investigation into the impact and flexural strength of light cure denture resin reinforced with carbon nanotubes. World Appl Sci J. 2012;18(6).
  12. Zafar MS, Ahmed N. Effects of wear on hardness and stiffness of restorative dental materials. Life Sci J. 2014;11(10 SPEC. ISSUE).
  13. Farina AP, Cecchin D, Soares RG, Botelho AL, Takahashi JMFK, Mazzetto MO, et al. Evaluation of Vickers hardness of different types of acrylic denture base resins with and without glass fibre reinforcement. Gerodontology. 2012;29(2).
  14. Leão R de S, Moraes SLD de, Gomes JM de L, Lemos CAA, Casado BG da S, Vasconcelos BC do E, et al. Influence of addition of zirconia on PMMA: A systematic review. Vol. 106, Materials Science and Engineering C. 2020.
  15. Asopa V, Suresh S, Khandelwal M, Sharma V, Asopa SS, Kaira LS. A comparative evaluation of properties of zirconia reinforced high impact acrylic resin with that of high impact acrylic resin. Saudi Journal for Dental Research. 2015;6(2).
  16. Ebrahim M, Seyam A, Gamal S. Effect of Zirconium Oxide Nano-Fillers Addition on Transverse Strength And Impact Strength of Heat-Polymerized Acrylic Resin, An in Vitro Study. Advanced Dental Journal. 2019;1(2).
  17. Gad MM, Abualsaud R, Al-Thobity AM, Baba NZ, Al-Harbi FA. Influence of Addition of Different Nanoparticles on the Surface Properties of Poly(methylmethacrylate) Denture Base Material. Journal of Prosthodontics. 2020;29(5).
  18. Chowdhury AR, Pragati K, Narendra PU, Sudhir M, Hemant S, Ajay G. Effect of Addition of Titanium Oxide and Zirconium Oxide Nanoparticles on the Surface Roughness of Heat Cured Denture Base Resins: An In-Vitro study. SVOA Materials Science & Technology. 2021;
  19. Abualsaud R, Aleraky DM, Akhtar S, Khan SQ, Gad MM. Antifungal Activity of Denture Base Resin Containing Nanozirconia: In Vitro Assessment of Candida albicans Biofilm. Scientific World Journal. 2021;2021
  20. Zhang Y, Wang X, Li H, Ni C, Du Z, Yan F. Human oral microbiota and its modulation for oral health. Vol. 99, Biomedicine and Pharmacotherapy. 2018.
  21. Vikram S, Chander NG. Effect of zinc oxide nanoparticles on the flexural strength of polymethylmethacrylate denture base resin. Eur Oral Res. 2020;54(1).
  22. Gad MM, Rahoma A, Al-Thobity AM, ArRejaie AS. Influence of incorporation of ZrO2 nanoparticles on the repair strength of polymethyl methacrylate denture bases. Int J Nanomedicine. 2016;11.
  23. Pourhajibagher M, Bahador A. Effects of incorporation of nanoparticles into dental acrylic resins on antimicrobial and physico-mechanical properties: A meta-analysis of in vitro studies. Vol. 12, Journal of Oral Biology and Craniofacial Research. 2022.

Disclaimer from Guident

The views and opinions expressed in articles published in Guident are solely those of the authors and do not necessarily reflect the views of the editors, the editorial board or the publisher, Ivory India. Guident does not endorse any product, technique or treatment described. Clinical content is intended for qualified dental and medical professionals and is not a substitute for individual clinical judgement. Guident, its editors and the publisher accept no liability for any consequence arising from the use of information published in the journal.

How to cite this article

Dr. Poonam Yadav, Dr. Suneetha Rao, Dr. Ashok. A Comparative Evaluation of Anti-Microbial and Three Physical Properties of High Impact Acrylic Resin After Incorporating Varying Percentage of Zinc Oxide and Zirconium Dioxide Nanoparticles – an in Vitro Study. Guident. 2025 Jul;18(8). Available from: https://ivoryindia.in/articles/research/a-comparative-evaluation-of-anti-microbial-and-three-physical-properties-of-high-impact-acrylic-resin-after.html

Related articles

More in Research

All 97 articles
Call for papers

Publish your clinical work in Guident

Original research, case reports and review articles are welcomed from clinicians and researchers worldwide. Every submission is assessed by the editorial board.